Samsung


Samsung Digital phone systems... including DCS, DCS Compact, DCS 50si, DCS 400si, iDCS 500, iDCS 100, DS 616

And Samsung Voice mail systems... including SVMi-4, SVMi-8, and Cadence.

This is a multi-step process which involves entering administrator level programming and then setting the date and time.  Programming can only be done from a 12 or 24 button display telephone.

  1. With your handset on-hook, press TRSF and then dial 200. Your display then shows ENABLE CUS. PROG. PASSCODE:
  2. Dial your 4-digit pass code 1234 (which is the default pass code).  The display then shows ENABLE CUS. PROG. DISABLE.  If the pass code 1234 does not work as stated, please see Samsung DCS Notes below.
  3. Dial 1 to enable. The display now shows ENABLE CUS. PROG. ENABLE.
  4. Press TRSF and the keyset will return to its idle condition.  Once you have entered administrative level programming, you must begin programming within 30 seconds.  Any delay of more than 30 seconds between keystrokes will cause the system to automatically exit the programming mode.
  5. Next enter the new date and time as follows:
    Press TRSF and then dial 505. The display then shows the current date and time setting on your system.  The example below shows Monday, April 7, 2003, 9:30 AM.
  6. OLD: 0  04   07   03  :  09  30
    NEW:WMMDDYY:HHMM.
  7. Enter the correct date using the dial pad as follows:
    W= Day of the week (0-6; Week begins on Monday and ends on Sunday)
    MM= Month (01-12)
    DD= Day of the month (01-31)
    YY= Last two digits of the year (01)
    HH= Hour (Use 24 hour clock and enter the range of 00-23)
    MM= Minutes (00-59)
    Press TRSF to store and exit programming.  If you have entered invalid data, you will receive an INVALID ENTRY message for three seconds.  Reenter the date and time.

 

SAMSUNG-PROSTAR 816 Plus

To Enable Customer Programming

With the handset on-hook, dial '#06'. The display shows [MMC DISABLED].
Dial the passcode and '1' then dial '#'
Password 4321

At this point, the customer programming is open

Setting the Time and Date

After you have enabled customer programming, you may begin the following steps:

Dial '#55'. Display shows[YY MM DD HH MM]
Dial new information as follows:
YY = Last two digits of the year
MM = Month (01 - 12)
DD = Day of the month (01 - 31)
W = Day of the week (1 -7 day of the week begins on Monday & ends on Sunday)
HH = Hour (Use 24 hour clock)
MM = Minutes (0-59)

Dial '#' to set current time & date. The phone returns to normal use

 

Samsung Prostar 816H

This is a multi-step process which involves entering administrator programming and then setting the date and time. Programming can be done from any display telephone.

  1. Enter administrator level programming with your handset on-hook, press #04.  Your display then shows MMC DISABLED.
  2. Dial your 4-digit pass code 4321 (which is the default pass code), followed by 1#.  At this time, customer programming is enabled. If the pass code 4321 does not work as stated, please see Prostar 816H Notes.
  3. Next enter the date and time, press #55 and the display will show:
    (YY MM DD W HH MM)
  4. Enter new information as follows:
    YY= Last two digits of the year (01)
    MM= Month (01-12)
    DD= Day of the month (01-31)
    W= Day of the week (1-7; Week begins on Monday and ends on Sunday)
    HH= Hour (Use 24 hour clock and enter the range of 00-23)
    MM= Minutes (00-59)  
  5. Dial # to finish setting the date and time.  The phone now returns to normal use and all display phones have been updated to the correct date and time by this action.

 

 

SAMSUNG-PROSTAR 56/120

Before any programs can be accessed, you must first open system programming using the passcode you have been assigned. This must be done using an 824 display keyset.

While on-hook dial '#20'
Display shows OPEN SYSTEM PGM - ENTER CODE: Display four digits passcode (1234). Display shows OPEN SYSTEM PGM - CLOSED
Press MUTE key. Display shows OPEN SYSTEM PGM - OPENED Press '#'. Keyset returns to idle condition.
Now press '#' and two digit program code you want to access. Follow the instructions for that program

Note: You must begin programming within 60 seconds. ONce in programming, any delay of more than 60 seconds between keystrokes will cause the system to automatically close programming.

Should it ever become necessary to correct date and time displayed on all the keysets, do so as soon as it is noticed that it is incorrect. Traffic reports and SMDR records will be of no value when the date and time are not correct.

Diplay Format:
W (Day of the week): Enter 0 for Saturday
MM (Month): Enter 01 for January and 12 for December
DD (Day of the month): Enter a number in the range of 01 - 31
YY (Year): Enter the last two digits of the year
HH (Hours): Use the 24 hour clock and enter a number in the range of 00-24
MM (Minutes):
Enter a number in the range of 00-59

Note: Failure to enter time in 24 hour clock will cause the date to change at 12:00 noon

First open customer programming

ACTION

Dial '#70' Display Shows SET CURRENT TIME YY MM/DD W HH:MM
Enter current date & time, e.g., 3:15 pm, Mon Jan 6th 1992 SET CURRENT TIME 92 01/06 1 15:15
Press '#' to store and exit If you entered invalid data, you will receive the [INVALID ENTRY] message for three seconds.
Re-enter the correct date and time. Should the information that you entered be incorrect, repeat the procedure

 

SAMSUNG-PROSTAR 1224

Before any programs can be accessed, you must first open system programming using the passcode you have been assigned. This must be done using an 824 display keyset.

While on-hook dial '#20' Display shows OPEN SYSTEM PGM - ENTER CODE:
Display four digits passcode (1234). Display shows OPEN SYSTEM PGM - CLOSED
Press MUTE key. Display shows OPEN SYSTEM PGM - OPENED
Press '#'. Keyset returns to idle condition.
Now press '#' and two digit program code you want to access.

Follow the instructions for that program

Note:
You must begin programming within 60 seconds. Once in programming, any delay of more than 60 seconds between keystrokes will cause the system to automatically close programming.

Should it ever become necessary to correct date and time displayed on all the keysets, do so as soon as it is noticed that it is incorrect. Traffic reports and SMDR records will be of no value when the date and time are not correct.

Diplay Format:
W (Day of the week): Enter 0 for Saturday
MM (Month): Enter 01 for January and 12 for December
DD (Day of the month): Enter a number in the range of 01 - 31
YY (Year): Enter the last two digits of the year
HH (Hours): Use the 24 hour clock and enter a number in the range of 00-24 MM (Minutes): Enter a number in the range of 00-59

Note: Failure to enter time in 24 hour clock will cause the date to change at 12:00 noon First open customer programming

ACTION

Dial '#70' Display Shows SET CURRENT TIME YY MM/DD W HH:MM
Enter current date & time, e.g., 3:15 pm, Mon Jan 6th 1992 SET CURRENT TIME 92 01/06 1 15:15
Press '#' to store and exit

If you entered invalid data, you will receive the [INVALID ENTRY] message for three seconds. Re-enter the correct date and time. Should the information that you entered be incorrect, repeat the procedure.